350se brace HT.
Moderator: Excalibur Marketing Dude
350se brace HT.
So is 1 inch from the riser joint a good place to set the brace HT. on a 350SE? I did not get a manual with my bow. thank you - alanr
Re: 350se brace HT.
I think the recommended brace height is 3/4" from the end of the riser.
Download a manual here: http://www.excaliburcrossbow.com/support/
On the back of the factory replacement string package:
Download a manual here: http://www.excaliburcrossbow.com/support/
On the back of the factory replacement string package:
When installing a string, It's important that its set to the correct brace height. For all Matrix Compact Recurve Technology crossbows, the string's brace height should be set at 3/4" back from the joint where the riser meets the rail. It's acceptable for the brace height to vary 1/8" forward or backwards from the 3/4" setting.
Micro Suppressor 400 TD (Two of 'em)
Bulldog 360 Blackout
Micro 360 TD Pro (Kryptek Altitude)
Matrix 380
Vixenmaster strings - Love 'em! | DrStirrup - Good stuff man!
Bulldog 360 Blackout
Micro 360 TD Pro (Kryptek Altitude)
Matrix 380
Vixenmaster strings - Love 'em! | DrStirrup - Good stuff man!
Re: 350se brace HT.
They really don't have much as far as a manual specific to the 350se - I also have an Ibex & the brace ht. between the two is quite a bit different. alanr
- wildcatter
- Posts: 1222
- Joined: Mon Sep 02, 2013 8:31 pm
- Location: N.W. Ohio
- Contact:
Re: 350se brace HT.
I always set to 1" from rail riser seam to string on all my Matrix models, if they drop below 3/4" I reset, my poi and speed stay consistent anywhere in between that measurement, and in thousands of shots in 330's to 405's, I have never broke a limb or limb tip,,, good luck.
Hunt Hard or Stay Home!
380 Mad Max, XB-30 Pro 18" ZombiesW/ 125 gr ST
330 Mad Max Custom XB-30 Pro 16" B.E.E. W/100 gr ST
Leica R-1000 - Zeiss 8X42 Conquest HD
On the Hunt for the next!!
380 Mad Max, XB-30 Pro 18" ZombiesW/ 125 gr ST
330 Mad Max Custom XB-30 Pro 16" B.E.E. W/100 gr ST
Leica R-1000 - Zeiss 8X42 Conquest HD
On the Hunt for the next!!
Re: 350se brace HT.
The Manuel I got with my 350 says one half to one inch on all matrix models
Re: 350se brace HT.
Yep..that is the perfect place to be for the Matrix brace height..... as the sting stretches you can keep twisting your string "COUNTER clockwise" to maintain a brace height between 7/8"-1" inch from riser/barrel seam to the front of your string.
Last edited by MTBighorn on Sat Sep 16, 2017 10:43 pm, edited 1 time in total.
Re: 350se brace HT.
When I got my 350 LE (I think same bow different package) My brace height was 1 1/4 So I called cs because there is no manual on these bows and was told that what I had was right so that's what I'm going with
Ron
Ron
Re: 350se brace HT.
Solid advice !wildcatter wrote: ↑Sat Sep 16, 2017 10:07 amI always set to 1" from rail riser seam to string on all my Matrix models, if they drop below 3/4" I reset, my poi and speed stay consistent anywhere in between that measurement, and in thousands of shots in 330's to 405's, I have never broke a limb or limb tip,,, good luck.
James : 1 - 19-20 Know this , My beloved Brothers : Let every person be quick to hear , slow to speak , slow to anger , for the anger of man does not produce the righteousness of God .
8ptbuk's Flemish Strings
[email protected]
8ptbuk's Flemish Strings
[email protected]