anyone use 125 gr slick tricks?
Moderator: Excalibur Marketing Dude
anyone use 125 gr slick tricks?
Does anyone here use the 125 gr slick tricks? I'm thinking of converting from aluminum bolts to carbon, and rather than add brass weights I thought I'd go for a heavier broadhead and get something for the weight. The 125 gr. has a 1/8" larger cutting diameter, versus the 100 grain. My only concern is if the larger blades reduce flight accuracy.
I use 125 grain montec G5 on Gold tips and they are just as accurate as target points. I havent done a lot of practice in the wind but that might effect things a bit but i wouldnt think significantly. I have shot 2 deer so far and one dropped right there (spinal tap) and the other ran about 50 yards before crashing.
I use 125 gr Slick Tricks with 20 " Bemans for 455-460 gr with use of my Paradox. Still get over 325 fps good KE and super accuracy.
Digger
2008 Y25 Relayer #593 Boo string, lumizone
2-1984 Relayer,
2-1992 Wolverine
Excal Phoenix, acudraw, VARizone
T.P. Titan TL4, acudraw 50, Varizone
Vixen, Steddy Eddy, Varizone
Martin Rage
Martin Jaguar
PSE Infinity
2008 Y25 Relayer #593 Boo string, lumizone
2-1984 Relayer,
2-1992 Wolverine
Excal Phoenix, acudraw, VARizone
T.P. Titan TL4, acudraw 50, Varizone
Vixen, Steddy Eddy, Varizone
Martin Rage
Martin Jaguar
PSE Infinity
-
- Posts: 37
- Joined: Wed Aug 17, 2005 10:26 am
- Location: Quebec City
Gerald
If the broadheads are otherwise the same, the heavier one will penetrate deeper. With the Slick Trick the 125 grain is slightly larger in the cutting diameter, and that would tend to make it penetrate less. However, the penetration gain caused by the extra weight tends to off set the loss caused by the larger cut.
Bolt speed would be a bit less with the 125 grain, but I shoot an Exomax, so I don't much care about bolt speed. It shoots flat, and the bolt speed gain by using the 100 grain broadhead isn't enough to interest me.. I like the extra cut size, so that's why I want the heavier broadhead..
If the broadheads are otherwise the same, the heavier one will penetrate deeper. With the Slick Trick the 125 grain is slightly larger in the cutting diameter, and that would tend to make it penetrate less. However, the penetration gain caused by the extra weight tends to off set the loss caused by the larger cut.
Bolt speed would be a bit less with the 125 grain, but I shoot an Exomax, so I don't much care about bolt speed. It shoots flat, and the bolt speed gain by using the 100 grain broadhead isn't enough to interest me.. I like the extra cut size, so that's why I want the heavier broadhead..
"Gun Control Laws"--trying to nag criminals into submission.
-
- Posts: 37
- Joined: Wed Aug 17, 2005 10:26 am
- Location: Quebec City
I think some one is confused on cutting dia of the slicktrick 100gr vs 125gr. The cutting dia on these two broad heads are the same 1 1/8" the 85gr is only 1".... see http://www.slicktrick.net/
I use both the 100 and 125gr and they both use the same inserts/blades....
I use both the 100 and 125gr and they both use the same inserts/blades....
Both 100 and 125 grain heads are available with 1" or 1 1/8" blades. I just got 4 packs of the Standard 125 gr. 1 inch.......Actually the one inch size is stronger and will give better penetration and is more accurate...bigger cut is not always better.
Scroll down to the bottom of the slick trick page and look at the order form.
SLICK TRICK BROADHEADS
3 Pack
1" Standard 100
$ 22.00
1-1/8" Magnum 100
$ 22.00
1" Standard 125
$ 22.00
1-1/8" Magnum 125
$ 22.00
1" Extra Blades 100 & 125
$ 10.00
1-1/8" Extra Blades 100 & 125
$ 10.00
Scroll down to the bottom of the slick trick page and look at the order form.
SLICK TRICK BROADHEADS
3 Pack
1" Standard 100
$ 22.00
1-1/8" Magnum 100
$ 22.00
1" Standard 125
$ 22.00
1-1/8" Magnum 125
$ 22.00
1" Extra Blades 100 & 125
$ 10.00
1-1/8" Extra Blades 100 & 125
$ 10.00
Gary, I agree with you on the bigger cut...When I purchased them and chatted with Gary from Slick Trick...he told me what my above post states on accuracy, penetration and durability...those are his comments...pertaining to the 1 inch cut.GaryL wrote:He changed it this year then, I see that. The SlickTrick was only ava. in 1 1/8".... As for more accurate with the 1" I reckon anything is possible but shucks I can hit the same hole with 1 1/8" blades. I like the bigger cut....more blood to follow
Like you said, when you are hitting the same hole, what does it matter!
Dave
Read that Deer Dave, last time I talked with Gary was Dec.04 when I ordered my last set of SlickTrick 100gr and a pack of spare blades. I also noticed he now has a neat information page on the SlickTrick and how too sharpen them if you want.
Most of my deer kills have left my slicktricks with one blade rippled or warped but still love'em....
Most of my deer kills have left my slicktricks with one blade rippled or warped but still love'em....