My first ever fletch job

UPSMAN · Post by **UPSMAN** » Sun Dec 02, 2012 9:37 pm

Well here they are. I am sure they are a far cry from a Bigjohn product. Guess I will see how they fly tomorrow. If all goes well, I have 6 more that have never been shot that will have to be stripped and re-fletched.

Boo · Post by **Boo** » Sun Dec 02, 2012 10:18 pm

Looks good!

UPSMAN · Post by **UPSMAN** » Sun Dec 02, 2012 10:25 pm

Thanks Boo, I appreciate all the advise that you have given me. I hope they shoot as good as you and some of the other guys say they do.

Big58cal · Post by **Big58cal** » Sun Dec 02, 2012 10:26 pm

They'd look a whole lot better covered in blood.

Be sure and post up some of those pictures.

vixenmaster · Post by **vixenmaster** » Mon Dec 03, 2012 8:00 am

Them be finer than frog hair. I see 2 diff types lighted nocks you be tryin'em out to see which be better ? Also who made them ?

papa bear1 · Post by **papa bear1** » Mon Dec 03, 2012 9:20 am

Very nice job Upsman, Did you use the AZ.EZ Fletch bolt and if you did, did you have to use any spacers to get the blazers the right distance from the noc ? the reason i ask is because i have one, But i'm not going to refletch untill after season is over, Don't want to change anything at this time....

Dave

Hester0305 · Post by **Hester0305** » Mon Dec 03, 2012 9:36 am

Looks like you did a fine job on those arrows. Just need some blood on them

UPSMAN · Post by **UPSMAN** » Mon Dec 03, 2012 10:23 am

papa bear1 wrote:Very nice job Upsman, Did you use the AZ.EZ Fletch bolt and if you did, did you have to use any spacers to get the blazers the right distance from the noc ? the reason i ask is because i have one, But i'm not going to refletch untill after season is over, Don't want to change anything at this time....

Dave

yes,I did use the EZ fletch bolt. I took the lumenoks off and just put the raw bolt in the fletcher. Doing it like that will give you a 1 1/4 in from end of blazer to end of shaft. Was going to leave lumenok on bolt but it was a pain in a$$ to get the bolt to go into the fletcher. Am going to shoot them after lunch. will report back with results.

UPSMAN · Post by **UPSMAN** » Mon Dec 03, 2012 10:30 am

vixenmaster wrote:Them be finer than frog hair. I see 2 diff types lighted nocks you be tryin'em out to see which be better ? Also who made them ?

According to Danny Miller, They are all lumenocs. When I ordered them, Danny was out of stock and he sent me some random ones that he said were laying around on his bench. He didn't even charge me for them. I called and told him to bill me for them but he wouldn't do it because he didn't have the exact ones I ordered.What a guy.

mr meat · Post by **mr meat** » Mon Dec 03, 2012 12:13 pm

they look good!!

cooterdog · Post by **cooterdog** » Mon Dec 03, 2012 2:44 pm

mr meat wrote:they look good!!

X2

Bones · Post by **Bones** » Mon Dec 03, 2012 2:55 pm

You'll like em!!

Excalibur Crossbow Forum

My first ever fletch job

My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job

Re: My first ever fletch job