sighting question....

Crossbow Hunting

Moderators: Bill T, Excalibur Marketing Dude

Post Reply
Knight
Posts: 42
Joined: Mon Sep 26, 2011 7:41 pm
Location: Central Ontario

sighting question....

Post by Knight » Thu Dec 13, 2012 2:05 pm

Sighting in varizone scope.

20 yards (crosshairs) is fine

10 yards (chevron) is fine

At 30 yards (chevron), bolts are starting to move up and left a bit. About 2 inches up and same left.

Happening with both field tips and broadheads. (they are flying the same).

I assume I should make the adjustment with the crosshairs (down and right a bit) at 20 yards and then try the 30 yard chevron again.

Or should it be a combination of crosshairs and speed dial adjustment??

Ibex
Posts: 80
Joined: Wed Apr 01, 2009 4:10 pm
Location: upper peninsula michigan

Re: sighting question....

Post by Ibex » Thu Dec 13, 2012 2:46 pm

I use a Vortex 3x crossbow scope and sight in using the second cross hair at 30 yards. The first cross hair is really close at 20 yards . That said, a cross wind will cause the arrow hit hit right or left.
Ibex, 3X-32 Vortex crossbow scope, GT Laser II, 125 gr. Marden Mini Mag Steel broadheads, 4 deer so far

colouredchameleon
Posts: 765
Joined: Sat Nov 24, 2012 6:44 pm

Re: sighting question....

Post by colouredchameleon » Thu Dec 13, 2012 3:49 pm

Try following the Video that came with your Crossbow for sighting in.
Skip 30 yards until you follow the Video instructions.

You will most likely find the speed ring setting needs to be adjusted and thats all. @ fifty ( 50 ) yards When 20 yards is set then go to ( 50 ) yards
Once you start to over think it you will spend a lot of time chasing your tail

Worked for me like a charm

see online video

http://www.excaliburcrossbow.com/phpBB2 ... =1&t=46051

Video 16

User avatar
Fatboyxc
Posts: 55
Joined: Tue Sep 18, 2012 4:31 pm
Location: Chatham, Ontario

Re: sighting question....

Post by Fatboyxc » Thu Dec 13, 2012 4:05 pm

I just sighted in my varizone...as per one of the members on here. I sighted it in at 20 yards with speed set to the lowest setting, then moved back to 40 yards & adjusted the speed on the scope until I was able to hit the bullseye at 40 yards. I only made 2 speed adjustments on my scope. But when I was back at 40 yards I noticed I didn't have my scope set perfectly up & down so I had to rotate the scope just a bit so that my crosshairs were lined up vertically & horizontally.

After you are hitting the bull @ 40 then take at shot at 30 yards & you should be good to go.

Hope this helps.
Growing Old.....Standard
Growing Up.....Optional

Just the toys are more expensive!

User avatar
robertyb
Posts: 2637
Joined: Mon Feb 06, 2012 8:35 pm
Location: Georgia

Re: sighting question....

Post by robertyb » Thu Dec 13, 2012 4:30 pm

Use crosshair and set up dead on at 20 yards using an aiming point on upper part of target.
Move target out to 40 yards and using the 2o yard crosshairs again aim at the same spot you shot at 20 yards and shoot. You will hit several inches low.
Now simply aim at top again (no arrow needed) with the 20 yard crosshairs and adjust your speed ring to where the 2nd (40 yard) chevron is on the arrow you shot at 40 yards.

You are now sighted in to 50 yards.
Wildlife Population Control Specialist

User avatar
Deerstalker
Posts: 611
Joined: Fri Aug 10, 2012 6:18 pm
Location: North Carolina

Re: sighting question....

Post by Deerstalker » Thu Dec 13, 2012 6:26 pm

This is how I adjusted my scope for vertical alignment. Set a level sidewise on the rail with the CB setting on a table and adjust for level with paper under one side of the foregrip. Once the CB rail is level then move the level to balance on the vertical adjustment turret and twist the scope until the vertical turret is level. You can also test the setting by hanging a rope with a weight at 15/20 yards and check the vertical alignment with the CB level on a table and/or rest. Hope this helps & here is a picture of my Equinox with the Nikon BoltXr scope.
Image

The scope rings are HIGH but I believe that MEDIUM would also work as the scope will hit the weaver style rail when trying to use the Excal rings.
Semper Fi

2012 Equinox
Firebolts & BEEs w Boltcutter & Slick Trick BHs 150gr
S-5 & Boo string, TT trigger, Nikon Bolt Xr scope
2012 Vortex w/S5 & Nikon Bolt Xr (son # 1)
2012 Axiom SMF w/S5 (son # 2)

quincyp
Posts: 4
Joined: Tue Dec 04, 2012 9:28 am

Re: sighting question....

Post by quincyp » Sun Dec 16, 2012 1:51 pm

I always use a plumb line/rope/string with weight at 20 yards. The turrents are almost always "off" in relation to the vertical crosshair. Even on some of my high end rifle scopes. My shadow zone turrents were off a bit. Level the bolt rail, and use a plumb line down range. You can also use a piece of paper with two vertical lines on it (about 1/2" apart") and a horizontal line through the center of them. Obviously the vertical lines and the horizontal need to be pefectly perpendicular. Then you can use a level to set that horizontal line (and therfore the target) downrange. The two lines make it easy to adjust your vetical crosshair, since the cross hair tends to cover up a single line.

Then, your scope crosshairs will be perfect. Do it right, and use a bit of blue lock tite and you will never have to mess with your scope mounting again.

Cheers!

strum
Posts: 3889
Joined: Tue Sep 07, 2010 5:35 pm
Location: Blairsville Ga.

Re: sighting question....

Post by strum » Sun Dec 16, 2012 2:00 pm

sounds like you need to adjust your speed ring a fraz and level your scope.
these little things dont show up much at closer ranges but become more of and issue as you get out there..
i think if you are shooting high at 30 then you need to adj the speed ring to a faster setting
Micro RTX
Nikon Bolt XR
BEE Arrows
Slick Trick Magnum
Unshot Beta Chrony
John3:16

peter p
Posts: 746
Joined: Thu Sep 25, 2003 10:31 pm
Location: Bolton, Ontario

Re: sighting question....

Post by peter p » Sun Dec 16, 2012 2:35 pm

This is what I do once the scope is installed and you are happy with the crosshairs.

Sight in at 20 yards with the main crosshair.
Make left/right, up/down adjustments until you get a bullseye.

Move back to 40 yards and use the 40 yard chevron.

Adjust speed ring until the arrow hits level with the bullseye (do not use the up/down adjustment on the scope for this. Use only the speed ring).

Then make the left and right adjustments until you get a bullseye.

Check again at 20 yards and it should be right on.
Your 30 and 50 will be too.

Peter

Post Reply