Ring Ht. ?

vixenmaster · Post by **vixenmaster** » Tue Feb 04, 2014 2:46 pm

I measured my low ring & it shows 3/16" Does anyone knowed what the Med. & high rings measure ? I am in the process of makin a small plate mount fer video cam.

MI Yeti · Post by **MI Yeti** » Tue Feb 04, 2014 3:17 pm

It seems to vary a lot between manufacturers in my experience , what height are you looking for ? I can try to help you locate what your after .

vixenmaster · Post by **vixenmaster** » Tue Feb 04, 2014 3:26 pm

I need a set of rings that measure 1/2" to scope tube openin. That may vary because diff ht's of diff Holo reflex red dots. So iam tryin to get measurements instead of buying half dz diff rings sets to eyeball, thx

MI Yeti · Post by **MI Yeti** » Tue Feb 04, 2014 3:40 pm

Yeah that would add up fast . i was trying to look for rings with the measurement listed, but have not seen any yet. those see though rings are usually very tall .

MI Yeti · Post by **MI Yeti** » Tue Feb 04, 2014 4:36 pm

http://www.midwayusa.com/product/136218 ... cm_vc=U112

has the height measurement listed . i have those in low on my Exocet and I have no complaints , solid rings . Looks like they have the height listed for most the rings they have . Hope that helps

wheelie · Post by **wheelie** » Tue Feb 04, 2014 6:37 pm

Medium "Hawke Rings" is 5/8th from bottom of ring to scope mount rail. So they are atleast 1/2 inch. Have no high rings here but assume they must be close to 1 inch.

Kegbelly · Post by **Kegbelly** » Wed Feb 05, 2014 7:03 am

Warne Maxima #202 is .525". They're split vertically so a little harder to put on but they're good rings, I've got 2 sets on rifles.

vixenmaster · Post by **vixenmaster** » Wed Feb 05, 2014 7:22 am

Those up-right split rings won't work fer my project. I will be usin jus the bottom halves of the set of rings.Then a 1/8"-3/16" plate. 4 holes drilled to use machine screws

Kegbelly · Post by **Kegbelly** » Wed Feb 05, 2014 7:42 am

Ahh, I see. Let me dig around in my spare parts when I get in from work this evening, might run across something.

Kegbelly · Post by **Kegbelly** » Wed Feb 05, 2014 7:56 pm

Vixenmaster, I've got some 1" aluminum rings, one set measures 3/8 and the other is .710, just a hair over 11/16. Nothing in the 1/2" range, but If either of these will work for you their yours.

Masterhunter · Post by **Masterhunter** » Wed Feb 05, 2014 8:21 pm

I just purchased a set of Leupold 55860 Rifleman 1" Medium Rings Matte Finish .897" Ring Height is how they were advertised.

Deerstalker · Post by **Deerstalker** » Wed Feb 05, 2014 9:10 pm

There is a chart at this site that may be useful for the information that you are looking for.

http://www.burrisoptics.com/sigrings.html

I believe that you would need a high ring if you need 1/5" between the bottom of the scope and the top of the mount rail.

Excalibur Crossbow Forum

Ring Ht. ?

Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?

Re: Ring Ht. ?