New Micro strap hardware
Moderator: Excalibur Marketing Dude
New Micro strap hardware
New strap hardware now to eliminate those pesky 1/8" Allen head shoulder bolts on the Micros. At least for the 355 anyway.
Blackout BD-Axe "Hatchet340"
Suppressor 400TD
Assassin 400Extreme
Suppressor 400TD
Assassin 400Extreme
Re: New Micro strap hardware
Thank-you for the update photo, I like the improved design.
EXCALFFLICTION 1991 ->>----------> 2024
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Re: New Micro strap hardware
Forgot to mention they now take a 5/32 Allen head.
Blackout BD-Axe "Hatchet340"
Suppressor 400TD
Assassin 400Extreme
Suppressor 400TD
Assassin 400Extreme
Re: New Micro strap hardware
Are the round barrel spacers aluminum or steel?
EXCALFFLICTION 1991 ->>----------> 2024
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Matrix 355
Huskemaw and Leupold crossbow optics.
Boo Strings
SWAT BH's and TOTA heads.
Teach Your Family How To Hunt So You Don't Have To Hunt For Your Family
Re: New Micro strap hardware
Aluminum
Blackout BD-Axe "Hatchet340"
Suppressor 400TD
Assassin 400Extreme
Suppressor 400TD
Assassin 400Extreme
Re: New Micro strap hardware
I'm sure this is obvious but I'm not understanding where they go on the bow? What is the advantage of the new hardware?
- Carnivorous
- Posts: 3751
- Joined: Sun Dec 25, 2005 12:56 pm
- Location: Belleriver Ontario
Re: New Micro strap hardware
That is a must have. I'm calling Dawn ASAP...
A touch of frost has heightened your awareness and your heart steadily beats in anticipation. Your senses are suddenly alert to the movement on the forest floor and you realize that the moment of truth is at hand.
Re: New Micro strap hardware
On the micro 355, it went under the limb strap to allow the limb a bit of movement. Similar to the airbrakes. Where as the 335 was sinched tight.snugs wrote:I'm sure this is obvious but I'm not understanding where they go on the bow? What is the advantage of the new hardware?
The original design was just some aluminum tubes over the stock shoulder bolts. Which had a tiny 1/8 Allen head and were almost always stripped on removal. This new system locks the spacer into place, and uses a much stronger(I assume, I just got them today) screw to hold it down.
I do not know if it is going onto all micros, but I can say for certain all new 355's are leaving with this setup.
I will add that this is not necessarily a requirement for most people, but if you remove your limbs often it's worth its weight in gold.
Blackout BD-Axe "Hatchet340"
Suppressor 400TD
Assassin 400Extreme
Suppressor 400TD
Assassin 400Extreme
Re: New Micro strap hardware
newest version of retired 405 revision uses spacers.
Re: New Micro strap hardware
I've just installed them now. I should have measure them prior to install, as the leave more space than the previous spacer did.
Blackout BD-Axe "Hatchet340"
Suppressor 400TD
Assassin 400Extreme
Suppressor 400TD
Assassin 400Extreme
Re: New Micro strap hardware
Can u post a picture of them installed?
Re: New Micro strap hardware
Blackout BD-Axe "Hatchet340"
Suppressor 400TD
Assassin 400Extreme
Suppressor 400TD
Assassin 400Extreme
Re: New Micro strap hardware
I hope they will fit the Matrix line also.
Wildlife Population Control Specialist