Cracked Executioners?

Crossbow Hunting

Moderator: Excalibur Marketing Dude

Post Reply
User avatar
Tangle Eye
Posts: 133
Joined: Mon Feb 19, 2018 12:21 am
Location: Jackson, TN

Cracked Executioners?

Post by Tangle Eye »

Yesterday I took out the aluminum flat nocks in 4 of my Executioners to replace them with Luminoks. To remove the old nocks, I screwed in a target point, heated it with a torch for 25 - 30 seconds, and then pulled the point/nock out with pliers. Inspecting the arrows where I had just removed the nocks, I noticed a hairline crack running for about 1/2 inch down the shaft of 3 of the 4! :thumbdown: Well that’s not good. I know the Luminoks can be a little tight and you might need to shave a tiny bit off to get a good fit but this was before I put them in.

Did I do something wrong here? What could have caused this? These nocks had not been removed before and were the ones in the arrows I bought from Wyvern several months ago. They arrows in question had been shot a good bit - a few hundred times maybe - but I wouldn’t expect this. I didn’t inspect the arrows before removing the nocks so I don’t know if the cracks were already there but I kinda doubt it.

Any help is appreciated.
———————————————————————————————————
Excalibur Assassin w/ Boo Force 10 string

If you always do what you always did, you’ll always get what you always got.
W.Miguire
Posts: 1662
Joined: Wed Jun 04, 2014 7:26 pm
Location: Washington Island Wisc.

Re: Cracked Executioners?

Post by W.Miguire »

You may have damaged your arrow when you heated them up . You want the lighted nock to fit snug but not to tight that it cracks your arrow. some time you will have to shave one of the knobs off of the nock , just take a little at a time.. if you heat up the field point take a wet paper towel and wrap it around the arrow tip this will help.
W.M.
Horizontal Hunter
Posts: 1050
Joined: Thu Jan 25, 2007 4:13 pm
Location: Western Massachusetts

Re: Cracked Executioners?

Post by Horizontal Hunter »

Using hot water on the stove will give you a lot more control over the temperature.

Bob
Vegetarian: vejiˈte(ə)rēən/noun: old Indian word for lousy hunter.
Excalibur Exocet, GT Laser II, 2" Bhoning Blazers 125g NAP Spitfire
User avatar
yukonjack
Posts: 26
Joined: Sat Jan 13, 2018 11:35 am
Location: New Jersey

Re: Cracked Executioners?

Post by yukonjack »

Go on You Tube ( How to remove a flat nock cheap, fast, easy ) looks like it will work for you if this helps Yukon
Hester0305
Posts: 2430
Joined: Sun Dec 18, 2011 6:23 pm
Location: North Carolina

Re: Cracked Executioners?

Post by Hester0305 »

By heating them sometimes they will crack, I don't use glue anymore on my aluminum nocks, I order them with the nocks loose. The reasoning behind this is because s I don't glue the nocks I use a plastic sandwich baggie and push the aluminum nock over the baggie and into the back of the arrow. The nock doesn't come out and you can remove them for luminocks anytime you want. Hope this helps.
Stryker Katana 360
Black Eagle Zombie Slayers
TruGlo Titanium X Hybrid Broadheads
User avatar
Tangle Eye
Posts: 133
Joined: Mon Feb 19, 2018 12:21 am
Location: Jackson, TN

Re: Cracked Executioners?

Post by Tangle Eye »

Good ideas about the wet paper towel, hot water, and the sandwich bag. I knew I’d get some good ideas here!
———————————————————————————————————
Excalibur Assassin w/ Boo Force 10 string

If you always do what you always did, you’ll always get what you always got.
User avatar
robertyb
Posts: 2845
Joined: Mon Feb 06, 2012 8:35 pm
Location: Georgia

Re: Cracked Executioners?

Post by robertyb »

All my BEEs came with press fit nocks installed. No glue on them so no heat is necessary. Just screw in a point and pull them out. You will probably need to cut off a tad of the shaft and refletch before using them again.
Wildlife Population Control Specialist
User avatar
Boo
Posts: 14299
Joined: Thu Dec 29, 2005 11:04 pm
Location: Newtonville, Ontario, Canada
Contact:

Re: Cracked Executioners?

Post by Boo »

Anytime an insert is heated, you run a risk of damaging a shaft. I never try to remove inserts that have been glued in by Cyanoacrylate glues. Methods of removal are not controlled enough for my liking. The pleasure just doesn't outweigh the possible pain.
If someone could figure out the actual amount of heat you can safely apply to a carbon shaft and what amount of heat it takes to compromise the bond of Cyanoacrylate glues, I might change my mind but in the mean time, I'll stick with the known and avoid the unknown.
Some people just like stepping on rakes
Post Reply